Faucet installation in Houston, fitted properly the first time

Faucet installation in Houston is the work of fitting the faucet level, sealing it cleanly, and checking the supply lines and shutoff valves behind it. A new faucet should sit level, seal cleanly, and shut off fully, with supply lines and shutoff valves that work. El Primo Lalo Plumbing installs kitchen and bathroom faucets in Houston, and checks the lines and valves behind them at the same time.

Quality Faucet Installation in Houston
  • Kitchen faucets
  • Bathroom faucets
  • Supply lines checked
  • Written scope firstYou approve the price before we start
  • Tested before we leaveEvery repair gets a pressure or flow test
  • Parts on the truckCommon fittings stocked for one-visit repairs
  • Clean work areaWe haul away old parts and debris

What Our Faucet Installation Service Includes

Every faucet installation includes the labor to remove the old fixture, set the new one, connect the supply lines, and test for leaks. We also check the shutoff valves and drain assembly while we are under the sink. Parts like a new supply line or a replacement angle stop are quoted before we install them, so you know the full price up front.

  • Old Faucet RemovalWe disconnect the supply lines and drain, cut or unbolt the old faucet, and remove it from the deck. Seized parts get cut with a tube cutter or oscillating tool, and we protect the countertop with a pad so nothing gets scratched.
  • New Faucet SettingWe set the new faucet with fresh Teflon tape, new supply lines, and a new drain assembly if needed. Sprayers, soap dispensers, and filtered-water taps get installed at the same time, and we align the handle and spout square to the sink.
  • Shutoff Valve CheckWe open and close the angle stops to make sure they work. If a valve is seized or weeping, we quote a replacement before we install it. A bad shutoff valve is the most common reason a simple faucet swap turns into a water damage call.
  • Leak TestingWe run hot and cold water for two full minutes and check every connection with a dry paper towel. The sprayer, drain stopper, and swivel spout all get tested before we call the job done.
  • Cleanup and Haul-AwayWe wipe down the sink, cabinet, and floor and haul the old faucet away. You get the model number, the cartridge type, and a short note on how to shut the water off under that sink.
Faucet Installation
Plumbing repairs in Houston | El Primo Lalo Plumbing

Faucet work for Houston homes

We install kitchen and bathroom faucets in houses, townhomes, and apartments across Houston. Every visit includes a shutoff valve check and a leak test before we leave.

  • Kitchen faucet swap
  • Bathroom faucet install
  • Shutoff valve replacement
  • Supply line replacement

Faucet work for Houston businesses

We install commercial-grade faucets in break rooms, restrooms, and kitchens. Work can be scheduled during business hours so tenants are not disrupted.

  • OfficesBreak room and restroom faucets
  • RestaurantsKitchen and hand sink faucets
  • RetailRestroom and utility faucets
  • MedicalBreak room and exam room faucets

Faucet Installation in Houston: More Than the Fixture

A faucet install is three jobs: the fixture, the supply lines and the shutoff valves. Old shutoffs often do not shut off, and a corroded supply line is the leak waiting to happen behind a new faucet. We check both before the new faucet goes on, because a new fixture on a failed valve is a callback, not a finished job.

Houston's hard water, about 8 grains per gallon on average, is why we talk about cartridges and aerators at install time. A faucet that is easy to service lasts longer here than one that is not. Remodel work in older homes often means new supply lines too, especially where galvanised pipe is still in place.

A new faucet on a failed shutoff is a callback, not a finished job.

How Our Faucet Installation Process Works

Every job follows the same five steps, whether it is a single bathroom sink in Montrose or a full kitchen faucet replacement Houston TX in a River Oaks home. Here is exactly what to expect from the moment we arrive.

  1. Shutoff and Inspection

    Shutoff and Inspection

    We shut off the water at the angle stops and drain the lines. Then we inspect the shutoff valves, supply lines, and drain assembly for corrosion or cracks. If a valve is seized or weeping, we replace it now rather than after it fails at 2 a.m. This step takes 10 to 15 minutes.

  2. Old Faucet Removal

    Old Faucet Removal

    We disconnect the supply lines and drain, then remove the old faucet from the deck. Seized mounting nuts get cut with a tube cutter or oscillating tool. We protect the countertop with a pad and clean the deck so the new gasket seats flat. Expect 20 to 40 minutes depending on corrosion.

  3. New Faucet Setting

    New Faucet Setting

    We set the new faucet with fresh Teflon tape on the threads, new supply lines, and a new drain assembly if needed. Sprayers, soap dispensers, and filtered-water taps get installed at the same time. We align the handle and spout so the faucet sits square to the sink.

  4. Connection and Testing

    Connection and Testing

    We reconnect the supply lines, open the angle stops, and run hot and cold water for two full minutes. Every connection gets checked with a dry paper towel for weeping. We test the sprayer, the drain stopper, and the swivel spout before we call the job done.

  5. Cleanup and Walkthrough

    Cleanup and Walkthrough

    We wipe down the sink, cabinet, and floor, haul the old faucet away, and walk you through the new fixture. You get the model number, the cartridge type, and a short note on how to shut the water off under that sink. Total job time is usually 1 to 2 hours.

Tools and Methods We Use for Faucet Installs

  • Plumber at work in a Houston home

    Tube cutter

    Cuts copper pipe and PEX tubing cleanly when a supply line or stub-out needs to be shortened or replaced. A clean cut is the difference between a leak-free joint and a call-back.

  • Careful professional plumbing work in Houston

    Press fitting tool

    Connects push-fit and expansion fittings to copper or PEX without soldering. It is faster and safer in tight cabinet spaces where a propane torch is a fire risk.

  • Local plumbing service area in Houston

    Propane torch

    Used for soldered copper joints when the code or the situation calls for a brazed connection. We keep a fire-rated pad on hand and follow local code on when soldering is allowed.

  • Plumbing work in progress in Houston

    Pipe wrench

    Loosens seized supply lines, angle stops, and drain fittings. A proper pipe wrench gives the leverage to break a corroded nut without cracking the sink or the valve body.

  • Plumbing services in Houston

    Plumber's auger

    Clears clogs in the P-trap and branch drain when a new faucet is installed on a sink that drains slowly. It is the right tool for a small clog before it becomes a main-line problem.

  • Plumbing services in Houston | El Primo Lalo Plumbing

    Leak detection microphone

    Finds hidden leaks in the wall or under the slab when a faucet problem turns out to be a supply line leak behind the cabinet. It saves tearing into drywall to find the source.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    2021 Uniform Plumbing Code with Houston Amendments compliance

    Every install follows the code standards for supply line sizing, shutoff valve placement, and drain connections. That matters when you sell the house or when an inspector looks under the sink.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    Supply line and shutoff valve replacement

    We replace the supply lines and check the angle stops on every install. A new faucet on old, corroded supply lines is a leak waiting to happen, and the parts cost less than a water damage repair.

When Houston Homeowners Call Us for Faucet Work

  • A kitchen remodel in a 1970s Spring Branch ranch home with original copper pipe and a seized shutoff valve.

    We replaced the angle stops with quarter-turn valves, installed the new kitchen faucet, and connected the sprayer and soap dispenser. The whole job took about 2 hours, including the valve replacement. The homeowner got a working shutoff, a leak-free faucet, and a kitchen that was ready for the countertop install the next day.

  • A bathroom faucet in a Montrose bungalow that had been dripping for months and stained the sink basin.

    We pulled the old faucet, cleaned the deck, installed a new bathroom faucet with fresh supply lines, and replaced the drain assembly. The job took 75 minutes. The drip stopped, the stain stopped spreading, and the homeowner's water bill dropped by a large amount a month.

  • A commercial break room in the Medical Center needed three faucets replaced during business hours.

    We scheduled the work for 6 p.m., installed commercial-grade faucets in three break rooms, tested every connection, and hauled the old fixtures away. The property manager had working faucets by morning and no disruption to the tenants during business hours.

  • A homeowner in Clear Lake bought a new faucet but could not get the old mounting nut off.

    We cut the seized nut with an oscillating tool, cleaned the deck, and installed the new faucet with new supply lines. The job took 90 minutes. The homeowner avoided a return trip to the store and got the faucet installed in one visit.

How Faucet Installation Works in Houston

Remodel-driven installs concentrate in the Heights, Montrose and River Oaks, where older homes get new kitchens and baths, and in Memorial where family kitchens are upgraded. Hard water makes serviceable cartridges worth choosing.

  • The HeightsRemodel-driven installs in bungalow kitchens and baths, often with new supply lines.
  • MontroseBungalow kitchen and bath upgrades where old shutoffs need replacing with the faucet.
  • River OaksHigh-use kitchen faucets where quality and serviceability matter most.
  • MemorialFamily kitchen upgrades; the faucet works all day, so the install has to be right.
  • Garden OaksMid-century bath and kitchen refreshes with new supply lines.
  • Hard waterAbout 8 grains per gallon on average, so cartridges and aerators need to be serviceable.

From problem to finished result.

  • Seized Shutoff Valve in Bellaire

    Before

    A homeowner in Bellaire bought a new kitchen faucet but could not shut the water off under the sink. The original 1960s angle stop was seized open, and the supply line was corroded.

    After

    We replaced both angle stops with quarter-turn valves, installed the new faucet with fresh supply lines, and tested every connection. The job took 2 hours and the water bill dropped by a large amount a month.

    Turn the shutoff valves open and closed once a year to keep them from seizing. If a valve feels stiff, call us before it fails.

  • Dripping Bathroom Faucet in Montrose

    Before

    A Montrose homeowner had a bathroom faucet that dripped constantly and stained the sink basin. The cartridge was worn out and the drain assembly was loose.

    After

    We installed a new bathroom faucet with a new drain assembly and fresh supply lines. The drip stopped, the stain stopped spreading, and the job took 75 minutes.

    Wipe the faucet dry after use and clean the aerator every six months to keep scale from building up.

  • Commercial Break Room in the Medical Center

    Before

    A property manager near the Medical Center had three break room faucets that leaked at the base and would not swivel. Tenants had been complaining for weeks.

    After

    We installed commercial-grade faucets in all three break rooms during business hours, tested every connection, and hauled the old fixtures away. The work was done by 9 p.m. and the tenants had working faucets the next morning.

    Schedule a yearly check on commercial faucets and shutoff valves to catch wear before it turns into a leak.

Faucet Problems We Solve for Houston Homes

A faucet problem is rarely just a faucet problem. It is usually a sign of something else under the sink. Here are the most common issues we find when we arrive for a faucet installation near me Houston TX call.

  • Dripping faucet that will not shut off

    Dripping faucet that will not shut off

    We diagnose the cartridge first. If a or cartridge is available, we rebuild the faucet. If the body is cracked or the parts are obsolete, we install a new faucet and replace the supply lines at the same time. A steady drip wastes 3,000 gallons a year and can stain the sink basin. The cause is usually a worn cartridge or O-ring, and the fix is often a rebuild or a full replacement if the body is corroded.

  • Low water pressure at one faucet

    Low water pressure at one faucet

    We remove and clean the aerator, check the shutoff valve, and test flow at the supply line. If the valve is the problem, we replace it. If the line is clogged with scale, we flush it before installing the new faucet. A clogged aerator or a failing shutoff valve can cut flow to a trickle. If the problem is in the supply line, it can spread to other fixtures.

  • Leak under the sink after a DIY install

    Leak under the sink after a DIY install

    We pull the faucet, inspect the supply lines and drain, and reinstall it correctly with fresh Teflon tape and new gaskets. If the cabinet floor is wet, we dry it and check for mold before closing up. A cross-threaded supply line or a missing gasket can leak slowly and rot the cabinet floor. By the time you smell it, the damage is already done.

  • Corroded shutoff valve that will not close

    Corroded shutoff valve that will not close

    We replace the angle stop with a new quarter-turn valve. That gives you a working shutoff under the sink and makes the next faucet repair a 20-minute job instead of a 2-hour one. If the valve will not close, you cannot shut the water off to the faucet. That turns a simple repair into a whole-house shutoff and a bigger job.

A clean install, tested connections, and a working shutoff under the sink.

  • Stop Hidden Leaks Early

    A dripping faucet wastes 3,000 gallons a year or more, and the damage happens under the sink where you cannot see it. We replace the supply lines and check the shutoff valves during every install, so the cabinet stays dry and the water bill stops climbing.

  • Better Water Pressure

    Old aerators and clogged cartridges cut flow to a trickle. A new EPA WaterSense-rated faucet restores strong flow at 1.5 gallons per minute or less, which saves water without sacrificing pressure. Most customers notice the difference the first time they turn the handle.

  • Code-Correct Connections

    We install to the 2021 Uniform Plumbing Code with Houston Amendments standards, using push-fit or expansion fittings where they belong and brazed copper where code requires it. That matters when you sell the house or when an inspector looks under the sink.

  • One Visit, Done Right

    Most standard faucet replacements take 1 to 2 hours. We bring the wax rings, supply lines, Teflon tape, and common adapters on the truck, so you are not making a second trip to the hardware store while the water is off.

What you receive

Clear records you can keep and share.

Written price

Full price before work starts

Leak test

Every connection checked

Old fixture haul-away

We take the old faucet with us

What to know before your faucet install

The faucet is only half the job. The shutoff valves and supply lines under the sink matter just as much, and they are the most common reason a simple swap turns into a bigger repair.

  • Check the shutoff valves

    If the angle stops are seized or weeping, replace them during the install. A working shutoff makes the next repair a 20-minute job instead of a 2-hour one.

  • Replace the supply lines

    Old supply lines can crack or clog. New lines cost little and prevent a leak that can rot the cabinet floor.

  • Match the faucet to the sink

    Check the hole spacing and deck thickness before buying. A faucet that does not fit the sink means a second trip to the store.

Local service area

Plumbing coverage in Houston

Outside these areas? Call and ask if we can reach you. (346) 776-8560

What Houston Customers Say About Our Faucet Work

  • I can't say enough about their service. They are prompt and responsive to questions. Attentive to cleaning up afterwards and wear shoe covers. Prices are good and he helped me choose compatible replacement faucet and garbage disposal. which I ran out and picked up while he did other repairs. Fransisco is such a kind person and my elderly mom has been so pleased.
    Ann BogranGoogle review
  • Excellent customer service and the best prices!! I highly recommend them! They came out in less than an hour and fixed everything quickly.
    Ana AlvarezGoogle review
  • I'm very happy with your service. He is very efficient and knowledgeable thank you primo Lalo!!!
    Naty MaqueiraGoogle review

Faucet Installation Questions Houston Homeowners Ask

Still wondering? (346) 776-8560

Local service team

Book Faucet Installation in Houston

Call (346) 776-8560 for a free estimate. We fit the faucet, check the supply lines and valves, and test everything before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.

Contact El Primo Lalo Plumbing

Call us at (346) 776-8560 to book faucet installation or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.

Call to book

The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.

Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.