Written summary
What failed and what we replaced
Faucet repair in Houston is the work of finding the worn cartridge, seat, supply line or shutoff valve and testing the faucet after. A dripping faucet wastes water during business hours and wears the fixture from the inside. El Primo Lalo Plumbing repairs kitchen and bathroom faucets in Houston, usually in one visit: a cartridge, a seat, a supply line or a shutoff valve, diagnosed first and tested after.
Every faucet repair includes diagnosis, the repair itself, and a test before we leave. Here is what is covered on a standard call and what we quote separately if we find it.


We repair kitchen, bathroom, utility, and shower faucets in houses and condos across Houston. Every visit includes a supply line and shutoff valve check so the fix holds.
We repair faucets in restaurants, offices, retail spaces, and multi-unit properties with minimal downtime. Scheduling works around your business hours and tenant access.
A faucet drip is almost always a cartridge or a seat. Hard water, about 8 grains per gallon on average in Houston, scales cartridges and wears seats, so drips are one of the most common repair calls in the city. A stiff handle, a leak at the base, or water under the sink point to different parts: the handle mechanism, the base seal, or the supply line and shutoff valve.
Repair beats replacement when the fixture body is sound. A cartridge swap, a new seat, a supply line or a shutoff valve costs far less than a new faucet and takes one visit. Replacement is the answer when the body is cracked, corroded through, or parts are no longer available. We show you the failed part so you can decide.
A drip is a worn part talking. Replace the part and the drip stops.
Every call follows the same five steps, whether it is a kitchen faucet in Bellaire or a bathroom fixture in a Medical Center high-rise. Here is what you can expect from the moment you call.

Used to loosen and tighten supply connections and shutoff valves under the sink without damaging the fitting.

Cuts copper pipe cleanly when a supply line or stub-out needs replacement during a faucet repair.

Used for soldering copper pipe connections when a supply line repair requires a new section of pipe.

Makes copper and PEX connections without solder when a supply line needs a fast, clean repair.

Finds hidden leaks in walls or under slabs when a faucet problem traces back to a line leak.

Inspects drain lines when a faucet repair reveals a slow drain that points to a deeper blockage.

Every repair follows the Uniform Plumbing Code as adopted locally. That covers supply line sizing, shutoff valve placement, and backflow protection on fixtures that require it.

We match the replacement cartridge to the fixture brand and model, using , , , and standard parts. A mismatched cartridge is a common cause of repeat leaks.
We inspect the fixture and the galvanized supply lines feeding it. If the faucet is repairable, we replace the cartridge and seats. If the supply lines are corroded, we quote a line repair alongside the faucet fix. The homeowner gets a dry faucet and a clear picture of the supply line condition, usually in one visit.
We trace the leak to the faucet body or supply connection, repair the failed part, and check the shutoff valves. We test under pressure before we leave. The cabinet stays dry and the homeowner avoids a cabinet replacement.
We schedule a single visit, bring cartridges for the common fixture brands, and repair all three faucets in one trip. We leave a written summary of parts replaced. The units are ready on schedule and the manager has a record for the property file.
We replace the shower valve cartridge, clear the mineral buildup, and test hot and cold flow. If the valve body is cracked, we quote a valve replacement. The drip stops and the handle turns smoothly again, usually within a two-hour visit.
Hard water scales cartridges everywhere in Houston, and older fixtures in the Heights, Montrose and River Oaks wear first. Kitchen faucets work hardest, so they drip first.
A homeowner in the Heights had a kitchen faucet that had been dripping for months. The cabinet base was swelling and the shutoff valve under the sink was seized. The faucet was a single-handle unit with a worn cartridge.
We replaced the cartridge and the seized shutoff valve in one visit. The drip stopped completely, and the cabinet base dried out over the following week. Total time on site was about 90 minutes.
We recommended running the faucet hot and cold weekly and checking under the sink for moisture once a month. A cartridge replacement every few years is normal in Houston's hard water.
A Bellaire homeowner noticed water staining the cabinet base under a bathroom sink. The faucet was a two-handle fixture with a cracked valve seat. The supply line was also starting to weep at the connection.
We replaced the valve seat and the supply line, then tested under pressure. The cabinet stayed dry, and the homeowner avoided a cabinet replacement. The repair took about an hour.
We suggested checking the supply connections every six months and replacing the supply line if it shows any cracking. Hard water speeds up wear on these parts.
A Clear Lake homeowner had a shower valve that dripped constantly and a handle that was stiff to turn. Mineral buildup had seized the cartridge, and the valve body was still in good condition.
We replaced the cartridge, cleared the mineral buildup, and tested hot and cold flow. The drip stopped, and the handle turned smoothly again. The visit took under two hours.
We recommended a water softener to reduce mineral buildup and extend the life of the valve. A cartridge replacement every few years is typical in this area.
Most faucet calls fall into a handful of failure types. Here is what we see most often and how we handle each one.

We replace the cartridge or reseat the valve, whichever has failed. Most constant-drip repairs finish in under an hour, and the drip stops completely once the new part is in. A steady drip wastes thousands of gallons a year and stains the sink basin. It also keeps water on the valve seat, which speeds up corrosion and can lead to a bigger leak inside the wall.

We trace the leak to the faucet body, supply line, or shutoff valve and repair the failed connection. We use brass fittings and Teflon tape on threaded joints and test under pressure before we leave. Water under the sink rots the cabinet base and can spread to the floor. Left long enough, it damages the subfloor and invites mold. Most under-sink leaks have been running for weeks before anyone notices.

We disassemble the faucet, clear the mineral buildup, and replace the cartridge if it is worn. Houston's hard water causes this often, and a new cartridge restores smooth operation. A seized handle usually means mineral buildup or a failing cartridge. Forcing it can crack the valve body and turn a simple repair into a fixture replacement.

We clean or replace the aerator, check the cartridge, and test flow. If the problem is in the supply line, we repair or replace the section so pressure returns to normal. A single fixture with low pressure usually points to a clogged aerator or a failing cartridge. Ignoring it can lead to a full loss of flow at that fixture.
A single dripping faucet can waste over 3,000 gallons a year, and a running toilet adds thousands more. We replace the failed cartridge or seat so the flow stops completely. You see the difference on your next water bill, usually within one billing cycle.
Water that drips under the sink rots the cabinet base and warps countertops. We trace the leak to its source, whether it is the faucet body, a supply line, or a shutoff valve, and fix it before the damage spreads. Most under-sink leaks we see have been running for weeks.
We schedule faucet repair Houston appointments during our hours — Monday through Sunday, 7:00 AM to 10:00 PM — and we call ahead with a real arrival window. A technician arrives with the common cartridges and supply lines already on the truck, so a standard kitchen or bathroom faucet is usually back in service in under two hours.
You get a price before we turn a wrench. faucet repair Houston Texas does not mean cheap parts. We quote the repair, explain what failed, and let you decide. If the fixture is beyond repair, we tell you that too and quote a replacement instead.
Clear records you can keep and share.
What failed and what we replaced
Hot and cold run before we leave
Brand and model of the replacement part
A dripping faucet is usually a worn cartridge or a scored valve seat, not a reason to replace the whole fixture. Knowing which part failed helps you decide between repair and replacement.
A cartridge controls flow and temperature on most single-handle faucets. A valve seat is the surface the cartridge seals against. Either one can fail and cause a drip.
If the faucet body is cracked or the finish is failing, replacement is usually the better value. A repair on a failing fixture often leads to a second call within a year.
Mineral buildup scores valve seats and seizes cartridges faster. A water softener reduces the buildup and extends the life of every faucet in the house.

Outside these areas? Call and ask if we can reach you. (346) 776-8560
The cartridge or seat inside the faucet has worn or scaled up. Houston's hard water speeds that wear. A new cartridge or seat stops the drip; the handle itself is rarely the problem.
Repair when the fixture body is sound and only a part has failed. Replace when the body is cracked, corroded through, or parts are no longer available. We show you the failed part so you can decide.
Usually a supply line, a shutoff valve, or the faucet base seal. We check all three, because water under a sink can also come from the drain trap or the disposal. Finding the source matters more than drying the cabinet.
Yes. Estimates are free, and you approve the written scope before work starts. We are open Monday to Sunday, 7:00 AM to 10:00 PM.
Call (346) 776-8560 for a free estimate. We find the worn part, replace it, and test the faucet before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.
Call us at (346) 776-8560 to book faucet repair or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.
The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.
Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.