Flat-price quote
Approved before any work starts
Garbage disposal repair in Houston is the work of clearing the jam or replacing the worn seal or failed motor — and saying plainly when replacement is the honest answer. A disposal that hums but will not turn, jams every week, or leaks under the sink is usually a jam, a worn seal or a failed motor away from working again. El Primo Lalo Plumbing repairs garbage disposals in Houston, and tells you plainly when replacement is the honest answer.
Every disposal repair visit includes the diagnostic and the standard parts that fail most often. If the unit needs a full replacement, we quote that separately before any work starts so you can compare.


We repair disposals in houses, condos, and rentals across Houston. You get a written estimate before work starts and a dry cabinet when we leave.
Restaurant and breakroom disposals take heavier loads than home units. We repair and replace them and check the drain line so service is not interrupted.
Disposal diagnosis splits three ways. A humming unit is usually jammed: something is caught between the plate and the ring, and the reset button and a jam key often free it. A leak under the sink is usually a seal, a flange or the drain connection. A unit that is dead, trips constantly, or leaks from the body itself is usually done, and replacement is the honest answer.
A disposal ties into the sink drain and the dishwasher connection, so a disposal problem can look like a drain problem and a drain problem can look like a disposal problem. We check the unit, the trap and the drain before deciding, because clearing a drain will not fix a jammed disposal, and replacing a disposal will not fix a blocked main.
Humming means jammed. Leaking means a seal. Dead means done. Know which before you start.
Five steps from your first call to a tested, dry, working disposal. No guesswork and no surprise charges.

Clears clogs in the P-trap and branch drain when a disposal jam pushes debris downstream. We run it after clearing the unit so the sink drains fully.

Used on stubborn clogs in the drain arm and trap. It reaches past the disposal outlet without damaging the housing.

Finds hidden drips behind the cabinet or under the floor when a disposal leak is not obvious. It saves tearing into drywall to locate the source.

Checks the branch drain and sewer line when a disposal backup keeps returning. It shows roots, offsets, or buildup that a snake cannot fix.

Cuts copper or PVC cleanly when a drain arm or supply line needs replacement during a disposal repair.

Makes fast, reliable joints on copper and PEX without soldering, which matters in tight cabinets where a torch is a fire risk.

Used for soldered copper joints on older Houston homes when a press fitting is not the right call.

Every drain and supply connection we touch follows the Uniform Plumbing Code. That includes proper trap arms, venting, and flange sealing so the repair passes inspection and holds up.
We dispatch a prompt tech, clear the jam, check the P-trap for debris, and test the unit with a full sink of water. If the motor is fine, the repair is quick and the written estimate is quoted before we start. The sink is usable again the same day, and the homeowner knows what not to put down the drain next time.
We diagnose a failed flange gasket and a tripped breaker, reseal the flange with a new mounting ring, and test the circuit. The tenant gets a dry cabinet and a working disposal in one visit. The repair is documented for the property file, and the landlord avoids a cabinet replacement.
We confirm the motor winding is gone, quote a replacement install side by side with the repair cost, and install a correctly sized unit the next morning. The dishwasher drain is reconnected and tested. The homeowner gets a quieter, stronger unit with a paperwork and no old parts left behind.
We clear the P-trap, run a drain snake down the branch line, and check the dishwasher connection. The disposal itself is fine, so we do not sell a replacement. The sink drains fast again, and the homeowner saves the cost of an unnecessary new unit.
Disposal repairs follow kitchen use, concentrated in family homes in Memorial and the Heights, and in Midtown and Downtown apartments where disposals work hard every day. Grease in the kitchen line is the companion problem.
A River Oaks homeowner had a disposal that hummed and would not spin after a dinner party. The sink held water and the cabinet smelled. The unit had a bone fragment jammed in the flywheel and debris packed in the P-trap.
We cut power, freed the flywheel, cleared the trap, and tested the unit with a full sink of water. The repair took under an hour and cost far less than a replacement. The sink drained in seconds and the smell cleared once the trap was clean.
Run cold water for 15 seconds before and after grinding, and avoid bones, coffee grounds, and rice. A monthly grind of ice and citrus peel keeps the ring clean.
A Midtown landlord found water under the kitchen sink and a disposal that tripped the breaker. The flange gasket had failed and water was dripping onto the cabinet base, which had started to swell at the seam.
We replaced the mounting ring and gasket, resealed the flange, and reset the breaker. The full-water leak test came back dry. The repair ran a written estimate and the cabinet base dried out without replacement.
Check under the sink monthly for moisture, and do not hang heavy items on the disposal or drain arm. A new gasket every 8-10 years prevents most flange leaks.
An 11-year-old 1/2-hp disposal in a Spring Branch home finally died after years of hard water scale. The motor winding was burned and the unit tripped the breaker on every reset. The homeowner was washing dishes in a bucket.
We quoted repair versus replacement and installed a 3/4-hp unit the next morning. The dishwasher drain was reconnected and tested, and the old unit was hauled off. The install ran a written estimate and the kitchen was back to normal by noon.
Run cold water while grinding and flush the unit weekly. With Houston's hard water, a water softener will extend the new unit's life by several years.
Most disposal calls fall into a handful of failure patterns. Here is what we see and how we fix it.

We cut power, free the flywheel with the hex wrench, and check the capacitor. If the motor is still good, we clear the trap and test the unit. If the winding is burned, we quote a replacement install on the spot. Holding the switch on while it hums burns the motor winding and turns a simple jam clearing into a full replacement. The flywheel is usually stuck on food debris or a foreign object.

We identify whether the leak is at the sink flange, the drain connection, or the housing seal. Flange and gasket leaks get a reseal; a cracked housing means replacement. Every repair gets a full-water leak test. A leaking housing or flange rots the cabinet base and can warp flooring within days. Left alone, it also grows mold in the cabinet.

We clear the P-trap and run a drain snake down the branch line if needed. We also check the dishwasher drain connection, which is a common source of buildup, and test flow before we leave. Slow draining means solids are building up in the P-trap or branch drain. Ignoring it leads to a full clog and a backed-up sink.

We test the circuit, check the reset button, and confirm power at the unit. If the disposal is drawing too much current, we diagnose the motor and quote the right fix instead of guessing. A tripped breaker or dead outlet can look like a failed disposal. Misdiagnosing it leads to an unnecessary replacement.
We stock common capacitors, flange gaskets, and mounting rings on the truck, so most garbage disposal repair Houston calls finish in one visit. You get your sink back before dinner instead of washing dishes in the bathtub for a week.
A leaking disposal housing can rot the cabinet base and warp flooring within days. Fixing a disposal leak repair Houston near me call early usually means a small repair instead of cabinet replacement and subfloor drying that runs into four figures.
A disposal that grinds poorly sends solids into the P-trap and branch drain, which is how a simple jam turns into a clogged main drain. We clear the trap, test flow, and confirm the unit drains fully before we leave.
Most 1/2-hp and 3/4-hp units last 8-12 years with proper care. If the motor spins free and only the capacitor or flange has failed, repairing it is the garbage disposal repair Houston Texas route and keeps a serviceable appliance out of the landfill.
Clear records you can keep and share.
Approved before any work starts
Full sink of water before we leave
What failed and what to avoid
A disposal with a good motor and a failed capacitor or flange is worth repairing. A unit with a burned winding or a cracked housing is not.
If the flywheel spins free and the motor hums, the winding may still be good. A burned smell or a breaker that trips on reset points to replacement.
Most units last 8-12 years. Past that, a repair may only buy a few months before another part fails.
A flange or gasket leak is a reseal. A crack in the housing itself cannot be repaired and means a new unit.

Outside these areas? Call and ask if we can reach you. (346) 776-8560
It is jammed. Something is caught between the plate and the ring. Turn it off, never put a hand inside, and call us. A jam key and the reset button free most jams; a unit that keeps jamming has a worn mechanism.
Usually a seal, a flange or the drain connection. A leak from the body of the unit itself means the unit is done. We find the source before deciding repair or replacement.
Repair when the problem is a jam or a seal. Replace when the motor is dead, the unit trips constantly, or it leaks from the body. We show you the fault so you can decide.
Yes. Estimates are free, and you approve the written scope before work starts. We are open Monday to Sunday, 7:00 AM to 10:00 PM.
Call (346) 776-8560 for a free estimate. We find the jam, seal or motor fault, fix it, and test the disposal before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.
Call us at (346) 776-8560 to book garbage disposal repair or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.
The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.
Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.