Written quote
Price confirmed before work starts
Garbage disposal installation in Houston is the work of a drain connection, a dishwasher connection and a seal, not just a unit under the sink. A new garbage disposal is a drain connection, a dishwasher connection and a seal, not just a unit under the sink. El Primo Lalo Plumbing installs garbage disposals in Houston with the flange sealed, the trap connected right, and the unit tested before we leave.
Every install covers the removal, the new unit, the connections, and the test. Here is what is included in a standard job and what counts as an add-on.


We install disposals in single-family homes, townhomes, and apartments across Houston. Every visit includes a check of the flange, the drain, and the shutoff valves under the sink.
Restaurants, break rooms, and commercial kitchens need disposals that keep up with volume. We install and service units around your operating hours so service is not interrupted.
A disposal install has three connections that all have to be right: the flange seal to the sink, the drain trap, and the dishwasher inlet where fitted. A bad flange seal leaks under the sink, a wrong trap connection smells, and a dishwasher inlet left plugged means the dishwasher will not drain. We test all three before we leave.
A new disposal is also the right time to look at the kitchen drain, because grease and food waste narrow the line over time. If the sink drains slowly with a new disposal, the problem is the drain, not the unit, and we check the line before the install, not after.
Flange, trap, dishwasher inlet. Get all three right and the disposal is done for years.
Five steps from the first phone call to a tested, running disposal. No surprises, no guesswork.

Used to loosen the drain fittings and the trap arm so the old unit can be removed without damaging the pipe threads.

Clears the trap arm and branch drain when the sink is slow after the install. A hand auger reaches most kitchen clogs without pulling the trap.

Used for longer clogs in the branch drain. The snake follows the pipe and breaks up grease and food solids that the disposal pushed down.

Inspects the line when the sink backs up repeatedly. The camera shows whether the clog is in the branch drain or the main sewer line.

Used when a copper supply line or drain connection needs to be soldered. We use it only when the joint cannot be made with a mechanical fitting.

Cuts copper pipe cleanly when a supply line or drain section needs to be replaced during the install.

Our drain and pipe tools include cutters and wrenches, which hold up to daily use and make clean cuts on copper and PVC.

Every install follows the UPC for the trap, the drain connection, and the dishwasher inlet. That means the trap arm is properly sized, the venting is correct, and the connection is made to code, not just to what fits.
We coordinate with the countertop and plumbing schedule, install the disposal after the sink is set, and connect the dishwasher and drain. We confirm the cabinet space and the electrical circuit before the unit is ordered. The kitchen is ready to use the same day the countertop goes in, with no second visit needed.
We diagnose the unit, confirm the motor has failed, and replace it with a 1/2 HP model. We also clear the trap arm, which was partially clogged with food scraps. The sink drains freely and the tenant has a working disposal the same day.
We remove the old unit, replace the corroded flange and gasket, and install a 3/4 HP disposer with sound insulation. We check the shutoff valves and supply lines while the cabinet is open. The new unit runs quietly and the cabinet stays dry. The old unit leaves with us.
We schedule the three installs in one morning, bring the units on the truck, and complete each swap in about 90 minutes. Invoices are itemized per unit. All three units are ready for move-in the same day, with no return trips.
Disposal installs follow kitchen remodels and replacements, concentrated in family homes in Memorial and the Heights, and in Midtown and Downtown apartments. Grease in the kitchen line is the companion problem everywhere.
The disposal leaked from the bottom housing into the cabinet. The sink base was damp, the flange was corroded, and the trap arm was partially clogged with food scraps.
We replaced the unit with a 3/4 HP disposer, installed a new flange and gasket, and cleared the trap arm. The cabinet was dried and tested. The sink drained freely and no leaks showed after a full cycle.
Run cold water for 15 seconds before and after grinding, and avoid putting grease or fibrous scraps down the drain. A monthly ice-and-citrus grind keeps the chamber clean.
The disposal tripped the breaker every few days. The motor hummed but would not turn, and the wiring at the switch was loose. The unit was more than 12 years old.
We replaced the disposal with a 1/2 HP unit, tightened the wiring at the switch, and confirmed the breaker size. The new unit ran without tripping, and the amp draw measured within spec.
Do not overload the disposer with large batches of scraps. Run it in short cycles with cold water, and check the reset button if it stops.
The sink drained slowly after a disposal install by another company. The trap arm was clogged with grease and rice, and the dishwasher line backed up into the sink.
We cleared the trap arm with a drain snake, checked the branch drain with a camera, and reconnected the dishwasher line. The sink drained at full flow and the dishwasher cycle finished without backup.
Flush the drain with hot water weekly and avoid pouring grease down the sink. A mesh strainer catches scraps before they reach the trap.
Some sink problems look like a disposal issue but start somewhere else. Here is what we see most often in Houston kitchens.

We cut power, clear the jam with the right tool, and test the motor. If the motor is weak or the windings are bad, we replace the unit. If the jam is the only issue, we clear it and check the drain for the debris that caused it. A humming motor with no movement means the flywheel is jammed or the motor is failing. Continuing to run it can burn out the motor or trip the breaker repeatedly.

We confirm the leak source, then replace the disposal. Bottom-housing leaks are not repairable. We also check the flange and trap for leaks while the cabinet is open. A leak from the bottom housing usually means the internal seal has failed. Water in the cabinet warps the sink base and can damage flooring.

We run a drain snake or plumber's auger through the trap arm and branch drain. If the clog is further down, we use a sewer camera to locate it. Clearing the line restores flow. A slow drain points to a clog in the trap arm or branch drain, not the disposal itself. Ignoring it leads to standing water and backups.

We check the circuit, the wiring at the switch, and the disposal's amp draw. If the motor is drawing too much, we replace the unit. If the wiring is the problem, we repair it before the new unit goes in. A breaker that trips every time the disposal runs points to a wiring issue, a failing motor, or an undersized circuit. Repeated trips are a fire risk.
A leaking garbage disposal can rot the cabinet floor and warp the sink base within weeks. We replace the mounting gasket, plumber's putty seal, and drain gasket so the new unit sits dry. Most leaks we find start at the flange or the dishwasher inlet, and both get checked during every garbage disposal installation services Houston call.
If you are resetting the breaker or reaching for an Allen wrench every week, the motor is on its way out. A new 3/4 HP unit grinds through everyday scraps without stalling. We size the motor to your cooking habits, so a family that cooks rice and stews daily gets more torque than a condo owner who mostly reheats.
A failing disposal sends food solids into the P-trap and the branch drain, which is how clogged main drain calls start. Installing a new unit with a properly seated baffle and a clean trap keeps scraps out of the line. We also check the drain snake reach and flow before we button up the cabinet.
Older disposals rattle the whole sink cabinet. Modern units with sound insulation and a balanced grind chamber run noticeably quieter. We set the unit level and tighten the mounting ring so vibration stays in the disposer, not in your countertop. Most customers tell us the new unit is the quietest part of the kitchen afterward.
Clear records you can keep and share.
Price confirmed before work starts
Every joint checked for leaks
Old unit removed and taken away
The unit is only one part of the job. The flange, the drain, and the electrical circuit decide how long the install takes and how well it holds up.
A corroded flange will leak even under a new unit. We check it before quoting. If it is pitted or seized, it gets replaced.
A slow drain is a sign of a clog, not a bad disposal. We test the flow and clear the trap arm if needed. Installing a new unit over a clogged drain just moves the problem.
A 3/4 HP unit draws more current than a 1/2 HP model. We confirm the breaker and wire gauge before wiring. If the circuit is shared, a dedicated line may be needed.

Outside these areas? Call and ask if we can reach you. (346) 776-8560
A plumber should install a disposal. The work involves the drain connection, the flange seal and the dishwasher inlet, and a bad connection leaks under the sink or leaves the dishwasher unable to drain.
A straightforward swap is usually a short visit. The job takes longer when the trap, flange or dishwasher connection also needs work. We give you a written scope before we start.
Not if the problem is the drain. A disposal grinds food; it does not clear grease or a blocked line. We check the drain before the install so you do not pay for a new unit to fix a clogged pipe.
Yes. Estimates are free, and you approve the written scope before work starts. We are open Monday to Sunday, 7:00 AM to 10:00 PM.
Call (346) 776-8560 for a free estimate. We seal the flange, connect the drain and dishwasher inlet, and test the disposal before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.
Call us at (346) 776-8560 to book garbage disposal installation or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.
The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.
Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.