Pipe repair in Houston, from pinhole leaks to burst lines

Pipe repair in Houston is the work of matching the repair to the pipe: a pinhole in copper, a cracked cast-iron section, a pipe split by a freeze. A pinhole leak in copper, a cracked cast-iron section, a pipe split by a freeze: each needs a different repair, and each needs testing after. El Primo Lalo Plumbing repairs water and drain pipe in Houston to the 2021 Uniform Plumbing Code with Houston Amendments, with a free estimate first.

Pipe Repair
  • Pinhole leaks
  • Cracked sections
  • Freeze splits
  • Written scope firstYou approve the price before we start
  • Tested before we leaveEvery repair gets a pressure or flow test
  • Parts on the truckCommon fittings stocked for one-visit repairs
  • Clean work areaWe haul away old parts and debris

What Our Pipe Repair Service Includes

Every pipe repair starts with a real diagnosis and ends with a pressure test. Here is what is covered in a standard repair, and what we quote separately when the job calls for it.

  • Leak Location and DiagnosisWe use a leak detection microphone and sewer camera to find the failure before we open a wall or slab. You get a plain explanation of what failed and why.
  • Cut-Out and ReplacementWe remove the damaged section with a pipe cutter or tube cutter and fit new pipe in the correct material: copper, PEX, PVC, CPVC, or cast iron.
  • Joint and Fitting WorkJoints are soldered, pressed, or crimped to match the material and code. We use brass fittings, Teflon tape, and pipe solder where they belong.
  • Pressure Test and Flow CheckWe pressure-test the repaired line and run water through it before we leave. You see the result, not just a promise.
  • Cleanup and WalkthroughWe haul off old pipe and debris and walk you through the repair. If we opened drywall or concrete, patching is quoted as part of the scope.
Pipe Repair
Plumbing services in Houston | El Primo Lalo Plumbing

Pipe repair for homes

Homes in Houston deal with slab leaks, frozen splits, and corroded lines that drop pressure over time. We find the failure, repair the line, and test it before we leave.

  • Under-sink supply leaks
  • Slab leak location and repair
  • Frozen pipe splits
  • Corroded galvanized replacement

Pipe repair for businesses

Restaurants, offices, and retail properties need repairs that keep the doors open and pass inspection. We schedule around your hours and document the work.

  • RestaurantsSupply and drain line repairs around service hours
  • OfficesRestroom and breakroom pipe repairs with minimal downtime
  • RetailScheduled repairs that keep the sales floor open
  • Property managersDocumented repairs for multi-unit and insurance needs

Pipe Repair in Houston: The Right Fix for the Pipe You Have

Houston homes carry four pipe generations, and each fails differently. Galvanised steel from before the 1970s rusts from the inside out. Copper develops pinhole leaks, and Houston's water chemistry and slab foundations make them surprisingly common. Cast iron scales and cracks. Polybutylene from the late 1970s to the mid-1990s is notorious for sudden failures. The material decides the repair.

Freeze damage is the sharpest seasonal cause. The split forms during the freeze and the leak appears on the thaw, with attic runs freezing first and leaking onto ceilings. A repair after a freeze has to be checked along the whole run, not just at the visible split, because a line can split in more than one place.

Match the repair to the pipe. Copper, cast iron, galvanised and PEX all fail differently.

How Our Pipe Repair Process Works

From the first call to the final pressure test, here is what you experience when you book pipe repair services Houston TX with us.

  1. Call and Triage

    Call and Triage

    You call, we ask where the water is and whether it is still running. If it is an active burst, we walk you through shutting off the main valve at the street or the house shutoff. That one step saves floors and ceilings. We book the soonest slot and tell you what to expect.

  2. Locate and Diagnose

    Locate and Diagnose

    On site, we use a leak detection microphone and a sewer camera to find the failure without tearing up the whole house. For slab leaks, we map the line and confirm the spot before we cut concrete. You get a plain explanation of what failed and why, usually within the first 30 to 45 minutes.

  3. Quote and Approve

    Quote and Approve

    We give you a written scope and a price before any repair starts. If we find a second issue, like a corroded shutoff valve or a root intrusion in the sewer line, we show you and quote it separately. You decide what gets fixed now and what can wait. No work happens without your go-ahead.

  4. Repair and Test

    Repair and Test

    We cut out the damaged section with a pipe cutter or tube cutter, fit the new pipe, and join it with solder, press fittings, or crimp rings depending on the material. Then we pressure-test the line and run water through it. Most single-point repairs take two to four hours.

  5. Clean Up and Walkthrough

    Clean Up and Walkthrough

    We haul off the old pipe, patch where we opened drywall or concrete when that is in scope, and walk you through what we did. You get the test results, the materials used, and a short list of what to watch. If we see a risk elsewhere in the system, we tell you now, not after it fails.

Tools and Methods We Use

  • Plumbing services in Houston

    Leak detection microphone

    Listens for the sound of escaping water under slabs and behind walls so we open one spot instead of a whole room.

  • Plumbing services in Houston | El Primo Lalo Plumbing

    Sewer camera

    Inspects drain and sewer lines for cracks, root intrusion, and offsets before and after repair.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    press fitting tool

    Makes fast, reliable press connections on copper and PEX without open flame in tight spaces.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    Pipe cutter and tube cutter

    Cuts copper and plastic pipe square for clean joints and proper fit.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    Propane torch and pipe solder

    Solders copper joints where code and access allow a traditional connection.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    push-fit and expansion fittings

    Provides code-approved push and crimp connections for repairs and transitions.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    Pressure testing

    We isolate the repaired section and pressure-test it before restoring water. A joint that does not hold gets redone before we leave.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    Material-matched joining

    Copper gets soldered or pressed, PEX gets crimped or expanded, PVC gets solvent-welded, and cast iron gets the correct coupling. No mismatched patches.

When to Call for Pipe Repair

  • You hear water running when nothing is on, or the water bill jumps without explanation.

    We locate the hidden leak with a microphone and camera, confirm the source, and repair the line before it damages the structure. The leak stops, the bill normalizes, and you avoid a bigger tear-out later.

  • A pipe bursts under the sink or behind a wall and water is spreading.

    We triage on the phone, help you shut off the main, and send a tech for emergency pipe repair Houston near me calls during our hours — Monday through Sunday, 7:00 AM to 10:00 PM. Water damage is limited, the line is repaired, and the area is tested before we leave.

  • You are remodeling a kitchen or bath and the old supply lines look corroded.

    We inspect the exposed pipe, replace failing sections with matched material, and update shutoff valves while the wall is open. The remodel closes up on sound plumbing instead of a future leak.

  • A freeze event splits an exposed line in the garage or attic.

    We repair the split, check nearby lines for damage, and pressure-test the system. Water is back on, and you know which lines to insulate before the next freeze.

How Pipe Repair Works in Houston

Pier-and-beam homes in the Heights, Montrose and the Third and Fifth Wards carry galvanised and cast-iron pipe, while slab homes in Sharpstown and Meyerland carry copper under concrete. Freeze damage hits attic runs across the whole city.

  • The HeightsGalvanised supply and cast-iron drains in pier-and-beam homes; repairs are accessible under the floor.
  • MontroseBungalow galvanised and cast iron; pinhole leaks and scaled drains are the daily calls.
  • Garden OaksMid-century copper and cast iron reaching end of life.
  • Third WardPre-1960s pier-and-beam stock with galvanised supply lines.
  • Fifth WardOlder homes where galvanised pipe rusts from the inside out.
  • Winter Storm UriIt dropped IAH to 12 degrees. Attic copper froze first, and the leak appeared on the thaw.

From problem to finished result.

  • Slab Leak in Meyerland

    Before

    A homeowner noticed a warm spot on the floor and a water bill that jumped sharply in one month. Two other companies quoted a full room tear-out without locating the leak.

    After

    We located the failure within 18 inches using a microphone and camera, opened one small section, repaired the copper line, and pressure-tested it. The patch was minimal and the bill returned to normal.

    We advised monitoring the water bill monthly and checking for new hot spots after seasonal soil shifts.

  • Frozen Burst in the Heights

    Before

    A hard freeze split an exposed line in a pier-and-beam crawlspace. Water was running under the house and the homeowner could not find the shutoff.

    After

    We walked the homeowner through the shutoff by phone, arrived during our hours, repaired the split section, and checked the rest of the crawlspace lines. Pressure test passed and water was back on by evening.

    We recommended insulating the exposed runs and sealing the crawlspace vents before the next freeze.

  • Corroded Galvanized in Garden Oaks

    Before

    A 1950s home had rusty water and low pressure at the kitchen faucet. A previous patch on the galvanized line was already leaking again.

    After

    We replaced the failing section with copper and added new shutoff valves. Pressure at the kitchen faucet came back to normal and the rusty water cleared within a day.

    We mapped the remaining galvanized runs and gave the homeowner a phased plan for replacement.

Pipe Problems We Fix in Houston

Most pipe failures in Houston fall into a few patterns. Here is what we see and how we handle it, including the burst pipe repair Houston TX calls that cannot wait.

  • Pinhole leaks in copper pipe

    Pinhole leaks in copper pipe

    We cut out the pitted section, repair with new copper or a proper transition fitting, and check the rest of the run for similar damage. Small leaks soak drywall and cabinets and can turn into a full split under pressure. They rarely fix themselves.

  • Slab leaks under the foundation

    Slab leaks under the foundation

    We locate with a leak detection microphone and camera, open one targeted spot, repair the line, and pressure-test before patching. Water under a slab can shift soil, crack flooring, and run up the water bill fast. Guessing at the location gets expensive.

  • Frozen and burst pipes after a freeze

    Frozen and burst pipes after a freeze

    We shut off the water, repair the split section, and check exposed lines for other weak points. We also advise on insulation for next season. A split line releases water fast and can flood a room in minutes. Houston homes are not always built for hard freezes.

  • Corroded galvanized or cast iron lines

    Corroded galvanized or cast iron lines

    We assess the run and recommend spot repair or replacement. When the line is too far gone, we quote pipe replacement or repiping with copper or PEX. Old lines rust from the inside, drop pressure, and eventually fail. Patches on failing pipe do not last.

A located, material-matched, pressure-tested repair that stays fixed.

  • Prompt Emergency Response

    Burst lines and slab leaks do not wait for business hours. We prioritize emergency pipe repair Houston calls. Call (346) 776-8560 during our hours — Monday through Sunday, 7:00 AM to 10:00 PM — and we will talk through the next step.. We shut off the water, isolate the failure, and stop the damage before it spreads.

  • Code-Correct Repairs

    Every repair meets 2021 Uniform Plumbing Code with Houston Amendments standards, and we pull permits when the job requires it. That matters at resale and when an inspector looks at a remodel. We use push-fit, expansion, and press fittings where they fit the application.

  • Right Materials for the Line

    Copper, PEX tubing, PVC, CPVC, or cast iron, we match the material to the line and the water. Copper pipe repair Houston homes need may call for soldered joints, while a PEX run in a crawlspace gets crimped fittings. No mismatched patches that fail next season.

  • Written Estimate First, No Surprises

    You get a clear price before we start. pipe repair Houston Texas does not mean cheap parts or skipped steps, it means honest scope and honest numbers. We tell you what the repair costs, what caused it, and whether a patch or a replacement makes more sense.

What you receive

Clear records you can keep and share.

Written scope

Clear price and work description before we start

Pressure test results

Proof the repaired line holds before we leave

Material list

What pipe and fittings went into the repair

What to know before you approve a pipe repair

The biggest cost difference in pipe repair is access, not parts. A repair that is located first stays small; a repair that is guessed at gets expensive.

  • Locate before cutting

    A leak detection microphone and camera find the failure before a wall or slab is opened. That keeps the repair targeted and the patch small.

  • Match the material

    Copper, PEX, PVC, and cast iron each need the right joint and fitting. A mismatched patch can fail within a season, especially under pressure.

  • Test before closing

    A pressure test confirms the joint holds before drywall or concrete goes back. Skipping that step is how a small leak becomes a second repair.

Local service area

Plumbing coverage in Houston

Outside these areas? Call and ask if we can reach you. (346) 776-8560

What Houston Customers Say

  • Came out to help one of my clients and he did honest, quality and fast work. Highly recommend them to anyone looking for plumbing.
    Roman CampuzanoGoogle review
  • Excellent customer service and the best prices!! I highly recommend them! They came out in less than an hour and fixed everything quickly.
    Ana AlvarezGoogle review
  • Very Professional, they were able to come out quickly and take care of everything. Their prices were way better than all the other plumbers i called as well. Definitely recommend them!
    Raul ÁlvarezGoogle review

Pipe Repair Questions Houston Homeowners Ask

Still wondering? (346) 776-8560

Local service team

Book Pipe Repair in Houston

Call (346) 776-8560 for a free estimate. We find the failed section, repair it to code, and test before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.

Contact El Primo Lalo Plumbing

Call us at (346) 776-8560 to book pipe repair or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.

Call to book

The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.

Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.