Pipe replacement in Houston, when repair is no longer enough

Some pipe is too far gone to repair: galvanised rusted through, copper pitted along a run, cast iron cracked end to end. El Primo Lalo Plumbing replaces failed pipe sections in Houston, in copper or PEX as the job requires, with a permit where the City requires one.

El Primo Lalo Plumbing — Plumbing you can rely on
  • Failed sections
  • Copper or PEX
  • Permitted where required
  • Written scope firstYou approve the price before we start
  • Tested before we leaveEvery repair gets a pressure or flow test
  • Parts on the truckCommon fittings stocked for one-visit repairs
  • Clean work areaWe haul away old parts and debris

What is included in a pipe replacement job

Every repipe includes the parts that matter: the new pipe, the fittings, the test, and the cleanup. Here is what you get when we open the wall, and what we price separately if the job needs it.

  • New pipe and fittingsCopper pipe, PEX tubing, or PVC pipe as the run requires, with brass fittings, press-fit or soldered joints, and Teflon tape on threaded connections. All materials are code-approved for Houston.
  • Shutoff valve replacementOld gate valves get swapped for quarter-turn shutoff valves at the main and at each fixture. You get a valve that actually closes when you need it to.
  • Pressure test and flushWe test the new line at 100 psi for at least an hour, then flush every fixture. Any weeping joint gets redone before we patch the wall.
  • Pipe insulationExterior and attic runs get pipe insulation to protect against freeze damage. Houston cold snaps crack unprotected lines, and insulation is cheap insurance.
  • Drywall patch and cleanupWe patch the openings we cut and haul the old pipe away. Floors get swept and vacuumed, and furniture goes back where it was.
Pipe Replacement
Plumbing services in Houston | El Primo Lalo Plumbing

Pipe replacement for Houston homes

Homes in Houston take a beating from hard water and hot attics, and old steel lines fail first. We replace the failing run, test it, and patch the wall before we leave.

  • Pinhole leaks in copper
  • Rusty water at taps
  • Low pressure upstairs
  • Burst pipe after a freeze

Pipe replacement for Houston businesses

A failed supply line can shut down a kitchen or a restroom bank. We schedule commercial repipes around your hours and test the line before we hand it back.

  • RestaurantsOvernight repipes so the kitchen opens on time
  • OfficesWeekend work in restroom and breakroom lines
  • RetailSupply line swaps with minimal floor disruption
  • RentalsPer-unit pricing for multi-unit properties

Pipe Replacement in Houston: Renew the Section, Not Just the Spot

Replacement is the answer when a pipe has failed along a section, not at a single point. Galvanised steel rusts from the inside out and narrows until pressure drops. Copper develops recurring pinholes. Cast iron scales, cracks and bellies. Polybutylene from the late 1970s to the mid-1990s is notorious for sudden failures. When the camera or the pressure test shows a tired run, replacing the section beats repairing it spot by spot.

Material choice matters. PEX is the common replacement for whole-house work because it routes overhead through walls and the attic, abandoning the under-slab line entirely. Copper remains the choice where the job calls for it. Bigger jobs such as whole-house repiping and sewer replacement need a City permit and inspection under the 2021 Uniform Plumbing Code with Houston Amendments.

Repair the point. Replace the run. Knowing which is which saves you the second call.

How our pipe replacement process runs

No mystery, no surprise drywall damage. Here is exactly what happens from the first call to the final pressure test.

  1. Call and scope

    Call and scope

    You call (346) 776-8560 and describe what you are seeing: low pressure, rusty water, a wet spot on the slab. We ask a few questions, then schedule a visit, usually prompt for active leaks. The visit includes a walkthrough and a leak detection check with a microphone or sewer camera if the line is underground.

  2. Written estimate

    Written estimate

    We map the run, count the fixtures, and price the job by the foot and by the fixture. You get a written number before any pipe is cut, including the cost to open and close the wall. If the scope changes mid-job, we stop and talk to you first.

  3. Demo and prep

    Demo and prep

    We shut off the water at the shutoff valves, drain the lines, and lay drop cloths over the floors. Furniture gets moved, cabinets get protected, and we cut only the drywall we need to cut. Most interior repipes take one to three days of demo and install.

  4. Install and test

    Install and test

    New copper pipe or PEX tubing goes in with brass fittings and press-fit or soldered joints. We insulate exterior runs, strap the pipe to code, and pressure-test the whole system at 100 psi for at least an hour. Any joint that weeps gets redone before we move on.

  5. Cleanup and walkthrough

    Cleanup and walkthrough

    We haul the old pipe out, patch the drywall openings, and flush every fixture. Then we walk the job with you, show you the new shutoff valves, and hand over the paperwork. You get a dry floor and a system that holds pressure.

Tools and methods we bring to a repipe

  • Plumbing services in Houston

    pipe cutter and press fitting tool

    Clean cuts and press-fit joints on copper and PEX. Press fittings go on in seconds and hold full pressure without a flame.

  • Plumbing services in Houston | El Primo Lalo Plumbing

    Leak detection microphone

    Finds hidden leaks under slabs and behind walls before we open anything. Accurate location keeps the repair small.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    Sewer camera

    Cameras the line to check for root intrusion in sewer line, offsets, and corrosion. We show you the footage before quoting.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    Propane torch and pipe solder

    Soldered copper joints where the spec calls for them. We use lead-free solder and test every joint at full pressure.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    Hydro jetting machine

    Clears scale and debris from drain lines after a repipe so the new pipe starts clean.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    push-fit and expansion fittings

    Push-to-connect and expansion fittings for PEX runs where a press tool will not fit. Code-approved and tested.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    2021 Uniform Plumbing Code with Houston Amendments

    Every repipe is strapped, insulated, and tested to the 2021 UPC with Houston Amendments. That means the inspection passes and the line performs the way it should.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    Pressure testing at 100 psi

    We test the new line at 100 psi for at least an hour before the wall goes back. Any joint that weeps gets redone, no exceptions.

When a repipe is the right call

  • A 1950s bungalow in Garden Oaks with galvanized steel lines and rusty water at every tap.

    We quote a whole house pipe replacement Houston TX with PEX tubing, run it through the attic and walls, and swap the shutoff valves at the same time. Clear water, full pressure, and no more pinhole leaks. The job takes three days and the drywall gets patched before we leave.

  • A slab leak in a River Oaks home that has already been patched twice in two years.

    We locate the leak with a microphone, then reroute the line overhead instead of breaking the slab again. New copper pipe and press fittings go in. The slab stays intact, the leak stops, and the homeowner avoids a foundation repair bill.

  • A restaurant in Midtown with a failing supply line that cannot close for a week.

    We schedule the commercial repipe overnight, isolate the kitchen line, and install new copper with shutoff valves at each station. The restaurant opens on time the next morning with a line that passes inspection.

  • A rental property near the Medical Center with a burst pipe during a freeze.

    We shut off the water, replace the burst section, and insulate every exterior run on the property. Photos and a written report go to the owner. The tenant stays in the unit, the owner has documentation for insurance, and the line is protected for the next cold snap.

How Pipe Replacement Works in Houston

Galvanised and cast-iron replacement concentrates in pier-and-beam homes in the Heights, Montrose and the Third and Fifth Wards, while copper-under-slab replacement is the Sharpstown and Meyerland job. Either way, the replacement routes overhead, not back under the slab.

  • The HeightsGalvanised supply lines in pier-and-beam homes, replaced overhead through walls and attic.
  • MontroseBungalow galvanised and cast iron at end of life; replacement beats another spot repair.
  • Garden OaksMid-century copper and cast iron where a tired run is replaced, not patched.
  • Third WardPre-1960s galvanised supply lines rusted from the inside out.
  • Fifth WardOlder homes where galvanised pipe has narrowed until pressure drops.
  • Expansive clayClay that swells and shrinks flexes slabs and shears buried lines, which is why replacements route overhead.

From problem to finished result.

  • Galvanized to PEX in a Heights bungalow

    Before

    A 1948 home with original galvanized steel lines. Water ran rusty at every tap, pressure upstairs was weak, and the owner had paid for four pinhole repairs in two years.

    After

    We replaced the full supply system with PEX tubing in three days. Pressure at the second-floor shower went from a trickle to full flow, and the water ran clear at every fixture.

    A water softener and an annual pressure check keep the new line in good shape. PEX does not corrode, so the main risk is freeze damage on exterior runs.

  • Slab leak rerouted overhead in River Oaks

    Before

    A slab leak under the living room floor had been patched twice. The homeowner did not want to break the slab a third time, and the flooring was starting to cup.

    After

    We rerouted the line through the attic with new copper pipe and press fittings. The slab stayed intact, the leak stopped, and the flooring dried out without replacement.

    Keep an eye on water pressure and watch for new wet spots. An overhead reroute removes the slab from the equation, so future leaks show up in the attic, not the floor.

  • Overnight commercial repipe in Midtown

    Before

    A restaurant with a failing supply line and a health inspection coming up. Closing for a week was not an option, and the line had been patched twice that year.

    After

    We ran the repipe overnight in two shifts, installed new copper with shutoff valves at each station, and pressure-tested before the morning shift. The restaurant opened on time.

    Quarter-turn shutoff valves at each station make future repairs a quick isolation instead of a full shutdown. We recommend an annual pressure check on commercial lines.

Problems a pipe replacement Houston TX solves

Most of our repipe calls start with one of these four problems. If you recognize yours, the line is telling you something.

  • Pinhole leaks that keep coming back

    Pinhole leaks that keep coming back

    We scope the line, find the pattern, and replace the failing section or the whole run. One job, one bill, no more patch-and-pray. Each leak costs a repair call and risks water damage to drywall, flooring, and cabinets. Three leaks in a year usually means the whole run is failing.

  • Rusty water and low pressure

    Rusty water and low pressure

    New copper or PEX restores full flow and clear water. We flush the system and test pressure at the furthest fixture before we leave. Corroded galvanized pipe narrows from the inside and sheds rust into the water. Shower pressure drops, and fixtures clog at the aerator.

  • Slab leak under the foundation

    Slab leak under the foundation

    We locate the leak with a microphone, isolate the line, and reroute or replace it. The slab gets tested before we close up. A slab leak can run for weeks before the wet spot shows. By then the flooring is cupped and the repair bill has grown.

  • Burst pipe after a freeze

    Burst pipe after a freeze

    We replace the burst section, insulate the exterior runs, and check the rest of the line for freeze damage so it does not happen again next winter. Houston cold snaps crack unprotected exterior lines. Water pours into the wall or attic, and the damage is worse than the pipe itself.

One repipe ends the repair cycle and restores full pressure.

  • Fewer emergency call-outs

    One pinhole leak usually means five more are coming. Replacing the run removes the weak section entirely, so you stop paying for emergency pipe replacement Houston near me visits at 2 a.m. Most customers go from three leaks a year to zero.

  • Stronger water pressure

    Corroded steel lines narrow from the inside out. New PEX or copper restores full flow to showers and fixtures, and you will notice the difference at the second-floor bathroom within a day of the swap.

  • Cleaner water at the tap

    Rust-colored water and metallic taste come from the pipe, not the source. Once the old galvanized pipe is out, the water runs clear. We flush and test every fixture before we call the job done.

  • Protects your slab and foundation

    A slab leak under a Houston home can run for weeks before you see it. Replacing the line before it fails protects the concrete, the flooring, and the drywall above it. That is the difference between a repipe and a foundation repair bill.

What you receive

Clear records you can keep and share.

Written scope

Pipe, fixtures, and drywall patch spelled out

Pressure test record

100 psi test logged before wall close

Photo documentation

Before and after shots for your records

Repair or replace: how to tell the difference

A single pinhole leak is a repair. A pattern of leaks is a replacement. The line is telling you which one you have.

  • Count the leaks

    Two or more leaks in the same run within a year means the pipe is failing. Patching again just delays the next call.

  • Check the water

    Rusty water at every tap points to a corroded main line. Clear water at one fixture points to a local repair.

  • Look at the material

    Galvanized steel older than 40 years is near the end of its life. Copper with green corrosion is close behind.

Local service area

Plumbing coverage in Houston

Outside these areas? Call and ask if we can reach you. (346) 776-8560

What Houston customers say about our repipes

  • Came out to help one of my clients and he did honest, quality and fast work. Highly recommend them to anyone looking for plumbing.
    Roman CampuzanoGoogle review
  • Very Professional, they were able to come out quickly and take care of everything. Their prices were way better than all the other plumbers i called as well. Definitely recommend them!
    Raul ÁlvarezGoogle review
  • Highly recommend!!! Thank you!!! Called and they showed up within 10 minutes!! (Cypress area) got the job done in about 15-20 minutes!
    Will BGoogle review

Pipe Replacement Questions Houston Homeowners Ask

Still wondering? (346) 776-8560

Local service team

Book Pipe Replacement in Houston

Call (346) 776-8560 for a free estimate. We show you the failed section, explain repair versus replacement, and renew it properly, Monday to Sunday, 7:00 AM to 10:00 PM.

Contact El Primo Lalo Plumbing

Call us at (346) 776-8560 to discuss pipe replacement or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.

Call to book

The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.

Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.