Written scope
What's included and what's quoted separately
Bathtub installation in Houston is the work of a drain, an overflow and a faucet connection, not just a tub in a hole. A new bathtub is a drain, an overflow and a faucet connection, not just a tub in a hole. El Primo Lalo Plumbing installs bathtubs in Houston with the drain sloped right, the overflow sealed, and the faucet tested, so the floor underneath stays dry.
Every standard install includes removal, haul-off, a new drain and overflow gasket set, and a level set on a proper base. Here's what's covered and what we quote separately if your job needs it.


We swap tubs in houses, condos, and townhomes across Houston. You get the old unit removed, the subfloor checked, and the new tub set level with new gaskets.
We replace tubs in rental units, apartment complexes, and assisted-living facilities on a schedule that keeps downtime low. Each unit is tested before we move to the next.
A bathtub install has three connections that all have to be right: the drain, the overflow and the faucet. The drain has to be vented and sloped, the overflow gasket has to seal, and the faucet has to shut off fully. A failure in any one of them shows up as a slow drain, water on the floor, or a drip that never stops.
Bath remodels drive most bathtub installs in Houston, especially in older homes in the Heights, Montrose and River Oaks. In slab homes, the drain work can mean concrete work, so we check the existing connections before the new tub arrives. Hard water makes a serviceable faucet cartridge worth choosing at install time.
Drain, overflow, faucet. Get all three right and the tub is done for years.
Five steps, one visit for most standard swaps. Here's exactly what happens from the phone call to the first shower.

Clears hair and soap scum from the P-trap and drain line before the new tub is set, so it drains fast from day one.

Cuts copper and PEX cleanly when a supply line or drain has to be moved for the new tub.

Makes leak-free copper and PEX connections in tight spaces behind the tub without soldering near framing.

Used for copper supply line connections where soldering is the right method and access allows it.

Finds hidden leaks in the wall or under the floor before we open anything up, so we fix the actual source.

Checks the drain line under the tub for root intrusion or a break before the new tub goes in.

Tub fillers and shower valves we install and set at the right height for the new tub.

We size the drain and overflow and check venting to the 2021 UPC with Houston Amendments. That keeps the install code-correct if you sell the house or get inspected.
We remove the old unit, check the subfloor and drain, and set a new acrylic or cast iron tub. We match the drain location so the surround doesn't have to be rebuilt. A clean, solid tub that's usable the same day, with the old one hauled off.
We measure the rough opening, confirm the drain location, and install the walk-in tub with the right fill and drain valves. We coordinate the electrical for the pump. A walk-in tub that fills and drains correctly, with the door seal tested before we leave.
We relocate the drain and supply lines, set the new tub, and tie the overflow and drain back in. We check the venting so the new location drains properly. A tub in the new spot that drains fast and doesn't gurgle, with the old drain capped off.
We schedule the swap for a single visit, protect the floor, and haul the old tub off. The tenant has a working tub the same day for most standard swaps. A code-correct install with minimal downtime for the tenant and a clean unit for the owner.
Bath remodels in the Heights, Montrose and River Oaks drive most installs, while Sharpstown and Meyerland bring slab-home drain work. Hard water makes the faucet cartridge choice matter.
A 1950s cast iron tub was rusted through at the drain and leaking into the ceiling below. The subfloor around the drain was soft, and the surround tile was cracked at the seam.
We cut the old tub out, repaired the subfloor, and set a new acrylic alcove tub on a mortar bed with new drain and overflow gaskets. The surround was re-caulked and the ceiling below was dry after the fill and drain test.
Keep the caulk line dry between uses and re-caulk every three to five years. Check the overflow gasket if you see a water stain below.
The family needed a walk-in tub for an aging parent, but the existing alcove was a standard 60-inch tub and the door seal on the old unit was failing. The drain was on the wrong side for the new tub.
We relocated the drain, set the walk-in tub, and coordinated the electrical for the pump. The fill and drain times were tested and the door seal was checked before we left. The tub fills in under four minutes.
Run the pump cycle weekly to keep the lines clear. Check the door seal for wear every few months and keep the drain screen clean.
A rental unit had a cracked fiberglass tub that flexed at the base and leaked into the unit below. The tenant needed a working tub fast, and the owner wanted minimal downtime.
We removed the cracked unit, checked the subfloor, and set a new tub on a foam bed in a single visit. The drain was tested and the unit was back in service the same day. The leak into the unit below stopped.
Use a drain screen to catch hair and avoid standing on the tub rim. Check the caulk line once a year and re-caulk if it pulls away.
Most tub calls come down to a handful of failures. Here's what we see most often and how we fix it.

We cut the old cast iron tub out, inspect and repair the subfloor, and set a new tub with new drain and overflow gaskets. The old tub gets hauled off before we leave. The leak rots the subfloor and stains the ceiling below. Left alone it can soften the floor enough that the tub starts to move when you step in.

We remove the cracked unit and set the new tub on a mortar or foam bed so it doesn't flex. The caulk line stays tight and the surround stays dry. A flexing base cracks the caulk line and eventually cracks the tub itself. Water gets behind the surround and into the wall.

We check the P-trap alignment and venting before the new tub goes in. If the drain has to move, we quote it first and do it right so the tub drains fast. A drain that wasn't aligned right or a trap that wasn't vented properly will back up and gurgle. It's a sign the rough-in wasn't done correctly.

We size the fill valve and drain for the tub, check the pump circuit, and test the fill and drain times before we leave. The tub works the way it's supposed to. A walk-in tub with the wrong valve or a restricted drain is frustrating and can be a safety issue for someone who needs it.
Most tub failures start at the overflow or shoe gasket, not the tub itself. When we set a new tub we replace both gaskets and pressure-test the drain before the surround goes back. That's the difference between a dry ceiling below and a water stain you find three months later.
A tub set on bare subfloor flexes every time you step in, and flex cracks the caulk line within a year. We bed the tub on mortar or structural foam so the base is solid. You'll feel the difference the first time you stand in it, and the caulk joint stays tight.
Houston follows the 2021 Uniform Plumbing Code with Houston Amendments on tub drains and overflow sizing. We size the drain, set the overflow at the right height, and make sure the trap is properly vented. That keeps the install clean if you ever sell or get inspected.
Walk in bathtub installation Houston Texas jobs need more than a bigger opening. The door seal, the fill and drain speed, and the dedicated circuit for the pump all have to be right. We handle the plumbing side and coordinate the electrical so the tub fills and drains correctly from day one.
Clear records you can keep and share.
What's included and what's quoted separately
Removed and taken away before we leave
Every joint checked before we leave
The tub is only half the job. The base it sits on and the gaskets under it decide whether it leaks in a year or lasts a decade.
A tub set on bare subfloor flexes and cracks the caulk line. A mortar or foam bed keeps it solid and quiet.
The shoe and overflow gaskets are the most common leak points. We replace both on every install, not just when they look bad.
If the new tub's drain doesn't line up with the rough-in, the drain has to move. We check that before we quote the job.

Outside these areas? Call and ask if we can reach you. (346) 776-8560
A plumber should install a bathtub. The work involves the drain, the overflow and the faucet connections, and a bad seal leaks into the subfloor where nobody sees it until the damage is done.
A straightforward swap is usually a short visit. A full remodel with new drain, overflow and faucet work takes longer, especially in slab homes. We give you a written scope before we start.
The overflow is the opening near the top of the tub that stops it flooding if the tap is left on. Its gasket has to seal, or water leaks behind the tub and into the floor. We test it as part of every install.
Yes. Estimates are free, and you approve the written scope before work starts. We are open Monday to Sunday, 7:00 AM to 10:00 PM.
Call (346) 776-8560 for a free estimate. We set the drain and overflow, fit the faucet, and test the tub before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.
Call us at (346) 776-8560 to book bathtub installation or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.
The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.
Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.