Shower installation in Houston, valve, drain and pan done right

Shower installation in Houston is the work of a valve, a drain and a pan connection, not just a head and a handle. A new shower is a valve, a drain and a pan connection, not just a head and a handle. El Primo Lalo Plumbing installs showers in Houston with the valve set right, the drain connected properly, and the pan tested, so the floor underneath stays dry.

El Primo Lalo Plumbing — your local Plumbing team
  • New showers
  • Valve and drain
  • Pan tested
  • Written scope firstYou approve the price before we start
  • Tested before we leaveEvery repair gets a pressure or flow test
  • Parts on the truckCommon fittings stocked for one-visit repairs
  • Clean work areaWe haul away old parts and debris

What our shower installation includes

Every shower installation Houston TX job we quote covers the plumbing work that makes the shower safe and serviceable. Finish tile and cosmetic wall repair are quoted separately when needed, and we tell you that up front so the scope is clear.

  • Old unit removalWe shut off the water, disconnect the drain and remove the old pan, valve and trim. We haul it off and protect the floor and nearby fixtures on the way out.
  • Valve and drain rough-inNew valve body set at the correct depth for your finish wall, new drain connection set level and centered. We check the subfloor and repair soft spots before the pan goes down.
  • Pan setting and waterproofingFiberglass bases get set in mortar so they do not flex. Tile showers get a pan liner and flood test before any tile goes up, so a leak shows up now and not next year.
  • Trim, head and handleWe install the trim, shower head and handle, then run hot and cold water and check every connection for leaks. Pressure balance or thermostatic valves are set to a safe temperature.
  • Permit and inspectionWhere the City of Houston requires a plumbing permit for the valve or drain work, we pull it and meet the inspector on site. You get the signed-off paperwork for your records.
Shower Installation
Residential plumbing in Houston

Showers for Houston homes

We replace leaking pans, failed liners and weak valves in houses across Houston. You get a written estimate before demo and a shower that drains and holds.

  • cracked fiberglass pan
  • failed tile pan liner
  • weak two-handle valve
  • tub-to-shower conversion

Showers for Houston properties

We install and replace shower units in rental units, gyms and small hotels. Work is scheduled around your operating hours so you do not lose a day.

  • Rental unitsPriority leak response and documented repairs
  • GymsCommercial valves built for daily use
  • Small hotelsScheduled installs around guest hours
  • SalonsShower pans and drains sized for heavy use

Shower Installation in Houston: Three Connections, One Test

A shower install has three connections that all have to be right: the valve, the drain and the pan. The valve controls temperature and flow, the drain has to be vented and sloped, and the pan has to hold water without leaking into the subfloor. A failure in any one of them shows up as a drip, a slow drain or water on the floor outside the shower.

Bath remodels drive most shower installs in Houston, especially in older homes in the Heights, Montrose and River Oaks. In slab homes, the drain and pan work can mean concrete work, so we check the existing connections before the new shower arrives. Hard water makes a serviceable cartridge worth choosing at install time.

Valve, drain, pan. Get all three right and the shower is done for years.

How our shower installation process runs

Every job follows the same five steps, whether it is a one-day swap or a full shower remodel plumbing Houston project. You know what happens each day and who is in your house.

  1. On-site assessment

    On-site assessment

    We shut off the water, open the wall behind the valve, and check the drain, subfloor and supply lines. You get a written scope and a written estimate before we cut anything out. Most assessments take 30 to 45 minutes.

  2. Demo and rough-in

    Demo and rough-in

    We remove the old pan, tile and valve, then set the new drain and valve body at the correct depth for your finish wall. If the drain line is cast iron pipe or the subfloor is soft, we address it now. This is the day the job is won or lost.

  3. Pan and waterproofing

    Pan and waterproofing

    The new base goes down level and solid, with the drain centered and the slope checked with a level. For tile showers we install the pan liner and flood-test it before any tile goes up. Fiberglass units get set in mortar so they do not flex or crack.

  4. Trim, valve and test

    Trim, valve and test

    We install the trim, head and handle, then run hot and cold water through the valve and check for leaks at every connection. The shower runs for several minutes while we watch the ceiling below and the drain connection.

  5. Cleanup and walkthrough

    Cleanup and walkthrough

    We haul off the old unit, wipe down the work area, and walk you through the shutoff location, the valve settings and how to care for the new pan. You get the final price we quoted, and we do not leave until the shower drains and holds.

Tools and methods we use on shower installs

  • Plumbing services in Houston

    Pipe cutter and press fitting tool

    Clean cuts and press connections on copper pipe and PEX tubing without open flame where the wall is tight. Faster and safer inside a finished bathroom.

  • El Primo Lalo Plumbing in Houston

    Propane torch and pipe solder

    Sweated copper connections where the code and the space call for them. We use a heat shield to protect framing and nearby finishes.

  • Plumber at work in a Houston home

    Sewer camera

    We scope the drain line before tying in a new shower drain, so a root intrusion in sewer line or a collapsed section is found before the pan goes down.

  • Careful professional plumbing work in Houston

    Leak detection microphone

    Finds water behind the wall or under the slab when the leak is not obvious. Saves opening the wrong wall on a shower replacement Houston TX job.

  • Local plumbing service area in Houston

    drain snake and plumber's auger

    Clears the shower branch line and the main drain before the new pan is set, so the shower starts with a clear drain.

  • Plumbing work in progress in Houston

    Level, tape measure and depth gauge

    Sets the valve at the correct depth for the finish wall and checks the pan slope. The difference between a trim that fits flush and one that does not.

  • Plumbing services in Houston | El Primo Lalo Plumbing

    2021 Uniform Plumbing Code with Houston Amendments rough-in

    Valve height, drain size and pan slope are set to code as adopted in Houston. We check the work against the code before the wall closes, not after the inspector arrives.

  • Plumbing services in Houston | El Primo Lalo Plumbing in Houston, TX

    Pan flood test

    For tile showers, the pan liner is filled with water and left overnight before any tile goes up. If it holds, the shower is watertight. If it does not, we fix it now.

When Houston homeowners call for a new shower

  • A tub-shower combo in a 1950s bungalow in Garden Oaks needs to become a walk-in shower for an aging parent.

    We remove the tub, relocate the drain as needed, set a low-threshold pan and add blocking for grab bars. The valve is replaced with a pressure-balance unit set to a safe temperature. A step-in shower with a curb under 4 inches, grab bar backing in place and steady water temperature, finished in four working days.

  • A rental unit in Midtown has a cracked fiberglass pan leaking into the unit below, and the tenant is still showering in it.

    We treat it as priority work, stop the water when we arrive, and schedule the pan and valve replacement within the week. The permit is pulled and the inspector meets us on site. The leak stops, the ceiling below dries out, and the unit is back in service without a second trip for paperwork.

  • A River Oaks home is updating a primary bath and wants a tile shower with a new drain line tied into the existing cast iron pipe.

    We scope the drain line with a sewer camera, replace the failing section, rough in the new valve and drain, and flood-test the pan before the tile setter starts. A tile shower on a sound drain line, with the plumbing inspected and signed off before the finish goes up.

  • A Clear Lake homeowner has weak shower pressure and thinks the shower head is the problem.

    We test pressure at the valve and find galvanized pipe feeding the shower. We replace that run with PEX tubing and install a new pressure-balance valve. Full pressure at the head and steady temperature, fixed at the source instead of with a gimmick shower head.

How Shower Installation Works in Houston

Bath remodels in the Heights, Montrose and River Oaks drive most installs, while Sharpstown and Meyerland bring slab-home drain and pan work. Hard water makes the cartridge choice matter.

  • The HeightsBungalow bath remodels where the valve, drain and pan are renewed together.
  • MontroseBath remodels in older homes where the valve is set in tile that needs care.
  • River OaksHigh-end bath remodels where the install has to be invisible and the pan perfect.
  • MemorialFamily bath upgrades; the shower works all day, so the install has to be right.
  • SharpstownSlab homes where drain and pan work can mean concrete work before the new shower goes in.
  • Hard waterAbout 8 grains per gallon on average, so the valve cartridge needs to be serviceable.

From problem to finished result.

  • Cracked pan to watertight walk-in

    Before

    A 1990s fiberglass shower in a Clear Lake home had a cracked pan leaking into the ceiling below. The valve was a corroded two-handle unit with weak, uneven pressure.

    After

    We removed the old unit, replaced the drain connection, set a new low-threshold pan in mortar and installed a pressure-balance valve. The ceiling below stayed dry through a 10-minute test run.

    Wipe the pan dry after use and check the caulk line at the drain twice a year. A water softener will keep the new valve cartridge clean.

  • Failed liner to flood-tested tile

    Before

    A 1970s tile shower in the Heights had a failed pan liner. The tile looked intact but the mud bed stayed wet and the dining room ceiling was stained.

    After

    We tore out the mud bed and liner, replaced the drain and subfloor section, rebuilt the pan and flood-tested it overnight. New tile went up on a pan that held water.

    Reseal the grout and caulk annually, and keep the weep holes at the drain clear so water does not sit in the pan.

  • Tub combo to step-in shower

    Before

    A Bellaire homeowner needed a step-in shower for a parent recovering from surgery. The existing tub-shower combo had a 15-inch tub wall and no grab bar backing.

    After

    We removed the tub, relocated the drain, set a low-curb pan and added blocking for grab bars. The valve was replaced and set to a safe maximum temperature.

    Check the grab bar screws every six months and keep the curb caulk sealed. The low curb stays easy to step over for years.

Shower problems we solve before they spread

Most shower failures start behind the wall and show up on the ceiling below. These are the problems we find on Houston shower replacement calls and how we stop them.

  • Cracked fiberglass pan leaking into the ceiling

    Cracked fiberglass pan leaking into the ceiling

    We remove the old pan, inspect the subfloor and drain line, and set a new base in mortar so it does not flex. The drain connection is checked with a level and the shower is run for several minutes before we leave. Water reaches the subfloor and the ceiling below for weeks before it shows. By then the drywall, insulation and sometimes the joists are wet, and mold has a foothold.

  • Failed pan liner under a tile shower

    Failed pan liner under a tile shower

    We tear out the old mud bed and liner, check the drain and subfloor, and rebuild with a new liner and a flood test. No tile goes up until the pan holds water overnight. A tile shower with a failed liner leaks slowly and constantly. The tile looks fine while the mud bed stays wet, and the damage spreads under the floor.

  • Low water pressure and scald swings

    Low water pressure and scald swings

    We install a pressure-balance or thermostatic valve and flush the line. If the supply is galvanized pipe, we replace that section with copper pipe or PEX tubing so the new valve gets full flow. Old two-handle valves and clogged cartridge screens make the shower weak and unpredictable. A sudden toilet flush can send the temperature from comfortable to scalding.

  • Drain set too high or off-center

    Drain set too high or off-center

    We set the new drain level and centered, check the slope with a level, and confirm the pan drains fully before the job is closed out. Water puddles in the pan and never fully drains. Over time the standing water stains the base and works at the caulk line.

A shower that drains, holds water and keeps steady temperature.

  • Stop hidden water damage

    A cracked pan or failed liner sends water into the subfloor and the ceiling below for months before you see it. We pressure-test the new pan and check the drain connection before the walls go up, so a shower replacement Houston TX job ends the leak instead of hiding it.

  • Fix pressure and temperature

    Old two-handle valves and clogged cartridge screens cause scald swings and weak spray. We install a pressure-balance or thermostatic valve set to the correct depth, then flush the line and confirm flow at the head. Most customers notice stronger, steadier water the same day.

  • Gain safe, low-step access

    A walk in shower installation Houston Texas project removes the 15-inch tub wall that makes stepping in risky. We set a low-threshold base, add blocking for grab bars, and keep the curb under 4 inches where the drain allows, which matters for aging parents and anyone recovering from surgery.

  • Protect resale value

    A dated, leaking shower is one of the first things a Houston buyer's inspector flags. A clean new pan, code-correct valve and properly sloped drain give you a documented upgrade, and we leave the shutoff valves and supply lines accessible so the next plumber can service them.

What you receive

Clear records you can keep and share.

Written scope

Flat price before demo starts

Flood test record

Pan held water overnight

Permit sign-off

Inspector approval on file

What to know before you replace a shower

A shower is a plumbing fixture before it is a tile job. The valve depth and the drain slope decide whether it works, and neither is visible after the finish goes up.

  • Valve depth

    The valve body must sit at the depth of the finish wall. Set too deep, the trim will not seal. Set too shallow, the handle will not sit flush.

  • Pan slope

    The pan must slope to the drain so water does not puddle. We check it with a level before the pan is set and confirm it drains fully.

  • Drain condition

    The drain line under the shower is often cast iron pipe in older Houston homes. We scope it before tying in a new drain so a failing line is not covered up.

Local service area

Plumbing coverage in Houston

Outside these areas? Call and ask if we can reach you. (346) 776-8560

What Houston customers say

  • We have used El Primo Lalo several times from fixing lawn sprinkler system, installing tankless water heater, fixing shower. Each time they have been extremely reliable, punctual, fair prices and totally trustworthy. We have recommended them to friends who have been equally satisfied. I would recommend them for any and all plumbing jobs.
    Ray YoderGoogle review
  • Excellent customer service and the best prices!! I highly recommend them! They came out in less than an hour and fixed everything quickly.
    Ana AlvarezGoogle review
  • I'm very happy with your service. He is very efficient and knowledgeable thank you primo Lalo!!!
    Naty MaqueiraGoogle review

Shower Installation Questions Houston Homeowners Ask

Still wondering? (346) 776-8560

Local service team

Book Shower Installation in Houston

Call (346) 776-8560 for a free estimate. We set the valve, connect the drain and pan, and test the shower before we leave, Monday to Sunday, 7:00 AM to 10:00 PM.

Contact El Primo Lalo Plumbing

Call us at (346) 776-8560 to book shower installation or ask a question. We are open Monday to Sunday, 7:00 AM to 10:00 PM, and estimates are free.

Call to book

The fastest way to book is a phone call. Tell us what is happening and we will give you a free estimate and a time that works, Monday to Sunday, 7:00 AM to 10:00 PM.

Open Mon–Sun, 7:00 AM–10:00 PM. Free estimates.